Fundamental Plumbing Guide for Installing a Bathtub
Fundamental Plumbing Guide for Installing a Bathtub
Blog Article
What're your opinions regarding Installing A Bathtub?
Mounting a tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably hard project. If the old bathtub is conveniently easily accessible, the task can move immediately; if you have to open a wall surface to get rid of the old tub and position the new bathtub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to leave the old bathtub and also embeded in the brand-new one. Ensure you have actually qualified yourself for the job and are comfortable trying it. Instead of employing a contractor to take control of a halfway-completed project, it is far better to consider utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will certainly assist you mount a new tub in your restroom if you have currently acquired a brand-new tub and do not need to change the arrangement of your previous supply of water pipelines.
Your tools as well as material list must comprise the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Making use of both wood boards under its feet, put the tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out level.
To install taps, fit all-time low of the furthest flexible faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and also check all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bathtub must wait up until the bath tub has actually been utilized a minimum of when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Protect the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The previous kind needs to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, causing the water to permeate the wall surface between the bathroom and also the tiling, bring about complications with dampness as well as possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, as well as can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that report about Tools You Need to Install a New Bathtub from someone on a different website. Do you know about anybody else who is interested in the subject? Please feel free to share it. Thanks for your time. Don't hesitate to check up our site back soon.
Urgent plumbing? Call us. Report this page